Winegard(R) Sensar(R) RV TV Antenna Technical and Customer Service Guide

Product Overview

The Winegard(R) Sensar(R) RV TV Antenna is a high-quality, durable solution for RV enthusiasts looking to receive clear television signals while on the move. This guide provides detailed information on replacement parts, installation procedures, and troubleshooting tips for the Sensar(R) RV TV Antenna and its upgrades.

Replacement Parts

Antenna Heads

• RVW-205: Amplified integrated Sensar/RV-WING antenna head. Installation requires a minimum of 16 inches clearance from the boom to any obstruction.
• RV-2005: Amplified Sensar III antenna head designed for situations where space from the boom to the nearest obstruction is less than 16 inches.

Upgrade Kits

• RV-WING (RP-4000/RP-4014): Snap-on UHF upgrade for Sensar II and III antenna heads (models made after 1990). Requires 16 inches clearance from the boom for installation.

Installation and Repair Components

• RP-2900: Includes 2 elevator tubes with 2 grommets.
• RP-0154: Comes with 4 pins, 4 retaining rings, and an adhesive rubber bumper.
• RP-2000: Leveling mount kit including 4 spacers, 2 pins, and 2 rings (for models purchased before 1990).
• RP-3000: Elevating gear.
• RP-4000/RP-4014: Worm gear and hex elevating shaft assembly (12.25 inches and 14 inches respectively), including wave washer, flat washer, o-ring, and worm gear nut.
• RP-2049: Gear housing kit with 2 pins, bearing, o-ring seal, 2 retaining rings, and nut.
• RP-6200/RP-6300: Directional handle and ceiling plate (Ivory and White), including 4 screws, spring (RP-6822), and decal.
• RP-6822: Spring for directional handle.
• RP-2658: Nylon bearing.
• RP-5895/RP-6795: Crank (Ivory and White) with set screw and hex/round shaft.

Additional Components

• FC-5932: RG-59 Weatherproof connector (12 pack).
• SA-1001: Ivory preassembled elevating shaft, gear housing, and base plate.
• RW-2000/IW-5012: Outside/Interior roof wedge for slanted roofs/ceilings.
• RP-0154: Boot for Sensar I and II models.
• EK-1036: Directional handle extension compatible with RP-6200/RP-6300.

Installation Instructions

1. Clearance Check: Ensure there is at least 16 inches clearance from the boom to any obstructions for the RVW-205 and RV-WING models. For RV-2005, ensure the space is less than 16 inches.
2. Mounting: Use the provided leveling mount (RP-2000) for models before 1990. For slanted roofs or ceilings, use the appropriate roof wedge (RW-2000/IW-5012).
3. Elevating Shaft Assembly: For RP-4000/RP-4014, assemble the worm gear and hex elevating shaft as per the included instructions.
4. Directional Handle Installation: Attach the directional handle (RP-6200/RP-6300) using the provided screws and spring. If needed, use the EK-1036 extension for additional reach.

Troubleshooting Tips

• Poor Reception: Check for obstructions around the antenna. Ensure the antenna is correctly aimed towards the broadcast towers.
• Mechanical Issues: Verify that all components, especially the elevating gear (RP-3000) and worm gear assembly (RP-4000/RP-4014), are correctly installed and functioning.
• Weather Damage: Inspect the antenna for damage after severe weather. Replace any damaged parts using the specified replacement components.

For further assistance, refer to the detailed installation and operating instructions provided with your Winegard(R) Sensar(R) RV TV Antenna. This guide is intended to be a comprehensive resource for customer service and technical staff in addressing common questions and issues related to the Winegard(R) Sensar(R) RV TV Antenna.