3 November: Over 90% of orders sent within 2 business hours. Posting Australia wide.
CaravansPlus Accessories Shop
Cart
CaravansPlus.com.au

Enerdrive eSYSTEM-E: 40A DC & AC Chargers - ePRO Plus Battery Monitor (600x490mm)

Enerdrive eSYSTEM-E: 40A DC & AC Chargers - ePRO Plus Battery Monitor (600x490mm)
Enerdrive eSYSTEM-E: 40A DC & AC Chargers - ePRO Plus Battery Monitor (600x490mm)
5 Year Warranty on all Enerdrive Branded Products
5 Year Warranty on all Enerdrive Branded Products
Enerdrive ePOWER 12V / 40Amp AC Battery Charger
Enerdrive ePOWER 12V / 40Amp AC Battery Charger
Enerdrive DC to DC Battery Charger w Solar Input - 12V / 40A
Enerdrive DC to DC Battery Charger w Solar Input - 12V / 40A
Enerdrive ePRO PLUS Battery Monitor
Enerdrive ePRO PLUS Battery Monitor
$2,938.00
$2,510
Made to order, Ships in 28 days.
Postage & ETA
Enter your postcode for delivery cost.

Description

This Pre-wired 600x490mm Power Board contains a 40A DC Charger with Solar input, 40A AC Charger and ePRO Plus Battery Monitor. Fitted with Fuse Block, Circuit Breakers & Cutout Switch they are designed for simple DIY Installation.

There is a full range of Enerdrive Installation Kits for 4WD Canopies, Caravans, Camper Trailers, Commercial Work Vehicles and more. They have been created in many different layouts and dimensional sizes to fit nearly every possible application. From small kits with AC & DC charging and battery monitoring up to kits with 2000w inverters and individual charge/load monitoring.

These kits are all pre-wired by Enerdrive where possible to keep the kits simple to install. All boards have a full wiring diagram showing each circuit and where to connect your loads, battery and inverter cabling. All items are mounted on a 12mm Black plastic (water & rot resistant) board for simple mounting into the application.

Features

  • Built & tested by Enerdrive for guaranteed performance
  • Simple DIY Installation by end user.

    Designed to maximise the following Enerdrive premium products

    Enerdrive ePower DC to DC Battery Charger w Solar Input - 12V / 40A

    The Enerdrive ePOWER DC2DC+ Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. DC charger features include:

  • Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output
  • DC M6 screw terminals that will allow for large battery cable connection between all sources
  • A dedicated Maximum Power Point (MPPT) solar regulator
  • The same battery algorithms as included in our AC mains ePOWER battery charger including a specific lithium charging profile
  • 40A output up to 40+ degrees C with thermo controlled fan cooling
  • Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage
  • Temperature sensor included in charger for more accurate battery charging

    Enerdrive ePOWER 12V / 40Amp AC Battery Charger

    The Enerdrive ePOWER 40A Battery Charger is a fully automatic, "set and forget" charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently.

    The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met. AC charger features include:

  • Multistage Charging: Fully automatic multistage battery charger with the ability to charge 3 separate battery banks.
  • Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three.
  • Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3.
  • Current Control: User adjustable current output (e.g. Dial the 60amp unit back to run off a 1kVA generator).
  • Smart Charging: The ePOWER 40A battery charger will regulate its output based on the loads connected to your battery banks.
  • Wide AC Input Range: Operates on both 110V / 60Hz and 240V / 50Hz.
  • LED Display: Easy to use "set and select" menu along with scrolling charger status.
  • Silent Mode: Disables the cooling fan for total silent operation at night or whenever required. Activation reduces charge output by half and locks out fan for 12 hours.
  • Temperature Sensor: Battery temperature sensor included with 3 meter cable.

    Enerdrive ePRO PLUS Battery Monitor

    The ePRO Plus is the latest generation, highly advanced battery monitor. It consists of an intelligent shunt and a remote control and display unit. The shunt has a Grid Optimized footprint for perfect integration with our DC Modular products.

    This advanced battery monitor not only shows the true state of charge of your battery system. It also offers a large amount of additional features to optimally supervise your battery system and control external equipment. The ePRO Plus is compatible with lead based and Lithium batteries (LiFePO4).

    The new ePRO Plus is equipped with an active shunt module. All measurements and calculations are made inside the active shunt module, resulting in the highest accuracy. The end results are transferred to the Control and Display Unit (CDU) over a digital cable connection, ensuring the highest immunity against external interference even in harsh industrial applications.

    The ePRO Plus can monitor up to three battery banks. The inputs for battery bank 2 and 3 can also be configured for other purposes, like mid-point voltage measurement, keyswitch input or backlight control. The ePRO Plus battery monitor can measure DC currents up to 600Amps (500Amp continuous) and voltages up to 70Vdc. So any lead - or lithium based battery from 12V up to 48V can be monitored. ePRO Plus Battery Monitor features include:

  • Complete battery status information at a glance (%, V, A, Ah, W, h:m, C)
  • Supports up to three battery banks (12V, 24V and 48V)
  • Very simple 'Plug and Play' installation
  • Perfect integration with Enerdrive DC Modular products
  • 5 year warranty.

Specifications

Further Information

Video Guide

Our Comments

The Enerdrive eSYSTEM Power Boards are made to order at Enerdrive's Factory and shipped directly to you. The expected lead time is around 4 weeks as each unit is meticulously constructed and tested by Enerdrive to ensure hassle free installation.

Enerdrive eSYSTEM Power Boards: The Ultimate DIY Guide for Caravan Enthusiasts

Enerdrive eSYSTEM Power Boards: The Ultimate DIY Guide for Caravan Enthusiasts

Information Articles, FAQ & Guides by the CaravansPlus Team...
Read

Related Products

Enerdrive Inverter & Lithium Warning Label Kit - AS/NZ 3001.2:2022

Enerdrive Inverter & Lithium Warning Label Kit - AS/NZ 3001.2:2022

3 In Stock Now.
$18.55
View
Enerdrive B-TEC 200Ah G2 Lithium Battery

Enerdrive B-TEC 200Ah G2 Lithium Battery

$2,825.00
$2,450
View
Enerdrive Cable Kit #1 Start Battery to DC to DC Charger (Vehicle Mounted)

Enerdrive Cable Kit #1 Start Battery to DC to DC Charger (Vehicle Mounted)

$205
View
Enerdrive Cable Kit #2 Start Battery To 50A Anderson Connector Mounted at the Tow Hitch

Enerdrive Cable Kit #2 Start Battery To 50A Anderson Connector Mounted at the Tow Hitch

$225
View
Enerdrive Cable Kit #3 Anderson 50A Connector to DC to DC Charger

Enerdrive Cable Kit #3 Anderson 50A Connector to DC to DC Charger

$240
View