Nothing in cart
Review of Caravans Plus Service
Very fast delivery after order was placed
1st order by Debbie from NSW
Enerdrive ePOWER 12V / 100Amp AC Battery Charger
$1,507.00
$1,290
Direct from supplier, Ships in 5 days.
Postage & ETA
Enter your postcode for delivery cost.
Description
The Enerdrive ePOWER 100A Battery Charger is a fully automatic, "set and forget" charger. It is designed to quickly and accurately recharge your batteries using algorithms that help maximise service life. Multistage smart charging technology enables the charger to be connected to your battery banks permanently.As dictated by battery manufacturer's recommendations, batteries require a multistage charge sequence for perfect, fast and accurate charging.
The Enerdrive ePOWER charger can be programmed for Lithium batteries. This setting delivers the full rated output of the charger constantly with the charger switching to power supply mode once the voltage peak is met (indicating a full battery bank).
Features
- Multistage Charging: Fully automatic multistage battery charger with the ability to charge 3 separate battery banks.
- Separate Battery Banks: Isolated charging design where battery bank one is separate from battery bank two and three.
- Programmable: Battery bank 1 can be programmed with a different charge algorithm over banks 2 and 3.
- Current Control: User adjustable current output (e.g. Dial the 100amp unit back to run off a 1kVA generator).
- Smart Charging: The ePOWER 100A battery charger will regulate its output based on the loads connected to your battery banks.
- Wide AC Input Range: Operates on both 110V / 60Hz and 240V / 50Hz.
- LED Display: Easy to use "set and select" menu along with scrolling charger status.
- Silent Mode: Disables the cooling fan for total silent operation at night or whenever required. Activation reduces charge output by half and locks out fan for 12 hours.
- Temperature Sensor: Battery temperature sensor included with 3 meter cable.
- 5 Year Warranty from an Australian company renowned for customer support.
- 5 year warranty.
Specifications
- Model: EN312100
- Brand: Enerdrive
- Barcode: 9342616028988
- Output Current Rating (Amps): 100 Amps
- Charger Mode Output Voltage: 14.2 - 15.5 V
- Float: 13.4 - 13.8 V
- Equalize: 15.5 V
- Charging Control: Four stages (Bulk/Absorption/Float/Maintenance), Two stages (Bulk/Absorption)Constant Power Supply (Program setting), Priority Battery Bank Charging
- DC Output: Three (1 fully independent, 2 common with diode isolation)
- Selectable Battery Type: Gel, AGM, Flooded, Lithium, Program
- Standby Current: < 5 mA
- AC Input Voltage: 90 to 265 VAC
- AC Input Operating Range: 207-265 Vac (7.6 A Max) 90-125 Vac (15.9 A Max)
- AC Input Frequency Range: 47 - 63 Hz
- Power consumption (DC 12V): 1750W (Full Load)
- Power Factor Correction: Yes
- Charger Efficiency: > 82%
- Reverse Polarity Yes, (with user replaceable fuse/s)
- Over Charge: Yes, unit shutdown
- Over Temperature Protection: Yes, unit de-rated and shutdown
- Cooling: Forced air ventilation (thermo controlled fan)
- Output Short Circuit: Protected, charger shutdown
- Temperature Setting: Hot, Normal, Cold (no sensor connected)
- Battery Temp Sensor Port: RJ12 (standard battery temp. sensor supplied)
- LCD Display: Charging status, Battery Voltage, Output Current & Fault Codes.
- AC Input Connection: IEC with Supplied 1.2M Power Lead
- DC Output Connection: Heavy Duty Terminal (3 banks) - Hex Nuts 8mm Thread
- DC Output Ground: Single Heavy Duty Common Ground Stud
- Storage Range (temp): -40 to 70 C
- Operating Range (temp): -20 to 60 C
- Humidity: 5-95%, relative humidity non-condensing
- Ingress Protection: IP32 (Basic drip proof in vertical orientation)
- Output System Voltage: 12V
- Dimensions(mm): 425 x236 x 102.7 (L x W x H)
- Net Weight (kg): 6.4 Kg
- Optional Accessories: Remote Digital Display / Enerdrive Part Number EN3REM
- Regulatory Compliance: Complies with AS/NZS 60335.2.29 Including Australian deviations.
Further Information
- View a summary of the related PDF: Product Manual (4.7MB)
Video Guide
Our Comments
The DC wiring used must be of appropriate size. An individual over-current protection device usually within 20cm of each battery bank is required. A DC disconnect switch is also recommended (this can be achieved by using a resettable breaker - see related items below)Enerdrive's recommended cable length, size and Fuse protection for the EN312100 are as follows: