29 March: Over 90% of orders sent within 2 business hours. Posting Australia wide.
CaravansPlus Accessories Shop
Cart
CaravansPlus.com.au

Air Pressure Switch - Camec Water Heater Spare Part #10

Air Pressure Switch - Camec Water Heater
Air Pressure Switch - Camec Water Heater
Air Pressure Switch - Camec Water Heater
Air Pressure Switch - Camec Water Heater
Air Pressure Switch - Camec Water Heater
Air Pressure Switch - Camec Water Heater
Air Pressure Switch - Camec Water Heater
Air Pressure Switch - Camec Water Heater
Camec Instant Water Heater Parts Diagram
Camec Instant Water Heater Parts Diagram
$110
16 In Stock Now.
Postage & ETA
Enter your postcode for delivery cost.
Postage: $9.30 (Combine & Save)

Stock Update - 29th March 2024

Yes, we have stock. Right now there are 16 of these held at our warehouse (Queanbeyan NSW).
Our stock levels are real and live. If you order now we will get it out with our next daily freight.
We aim to hold the most stock and have the fastest delivery on all caravan accessories and spare parts.

Description

If your Camec Water Heater is giving you an Error Code E9 (failure of pressure switch) its possible that the air pressure switch is faulty. This item in not repairable and must be replaced however E9 can indicate a higher than normal moisture content in the air pressure switch, which may prevent start-up of the HWS.

A solution to clear the E9 code can be to reduce the humidity level within the air pressure switch and/or air tubes.

For safety reasons, turn off the HWS at the control pad. Then turn off all gas bottles that supply the HWS. Then:
1. Using the supplied key, unlock and carefully remove the external white or black access door. Note, the exhaust protrudes through this door.
2. If the caravan or motorhome is not enclosed within a dwelling or garage, wait one (1) minute to allow any gas fumes to disperse. If caravan or motorhome is enclosed in a dwelling or garage, open all doors/roller doors and wait 5 minutes to allow any fumes to disperse.
3. Never allow any naked flame or electric hair dryer or appliance to enter the confines of the HWS unit. 4. Now identify and locate the air pressure switch, twin separate almost clear silicone air hoses joining the air pressure switch and the bottom of the 50mm metal exhaust. The air pressure switch is located at the Left Rear side of the HWS, approximately 150mm from the top and appears as a light grey plastic disc approximately 60mm diameter with two (2) separate silicone hoses attached.
5. Remove top silicone hose from air pressure switch and gently pull the hose to the outside of the HWS. Now with a hair dryer set to low heat and low fan cycle allow some warm air to enter silicone tube. This air will expel via the exhaust. Do not pressurise the hose as gentle air flow is all that is necessary, for say one (1) minute. Then re-attach hose.
6. Now do the same as 5. Above, but with the bottom silicone hose from air pressure switch. When procedure is complete, re-attach hose. At this point both top and bottom hoses on air pressure should be attached
7. Remove hose from bottom of exhaust vent, choosing the one closest to you. There are two (2) separate hoses, one behind the other. Gently pull the hose to the outside of the HWS then use hairdryer set to low heat and low fan cycle again to get some airflow into the hose, for one minute. Then reattach the hose.
8. Now, remove hose from bottom of exhaust, the hose further away from you this time, and use hairdryer for 1 minute. Do not pressurise the hose, reattach the hose.
9. Check again to ensure two (2) hoses attached to air pressure switch and other ends attached to exhaust vent. Refit the external access door.
10. Turn gas bottle(s) back on
11. Turn control pad back on and restart

If unit fails to start up, you have a faulty air pressure switch.

Features

  • 1 year warranty.

Specifications

Related Products

Spare Part Diagram - Camec Instant Water Heater

Spare Part Diagram - Camec Instant Water Heater

View